DV SDI Series 5 / 13 HP Reciprocating Air Compressors

Simple, Rugged and Cost-effective, the DV SDI Series 5 / 13 HP Reciprocating Air Compressors are a perfect match for both industrial and commercial uses.

Featuring splash-lubricated, cast-iron pumps manufactured for big air delivery at low speeds, these units function dependably, with minimal downtime.

Simple to install, Two-Stage Models are pre-wired with magnetic starters and single-stage models do not need a starter.

Providing 13 to 21 SCFM of compressed air at 125/150 psi, the SDI Series utilize 5 to 10 horsepower Open Drip Proof (ODP) industrial-grade motors with overload safeguards, or a 13 horsepower gasoline Honda motor.

DV SDI Series 5 /13 HP Reciprocating Air Compressors Benefits
  • Simple, Rugged and Cost-effective
    Perfect for either Industrial or Commercial applications
  • Cast-Iron Compressor Pumps
    High Air distribution at lower speeds
  • Dependable and Safe
    OSHA Fully-Enclosed Belt-Guard, Motor with Overload Protection, CRN and ASME Approved Air Receivers
  • Manufactured for simple installation
    Two-Stage Models Pre-Wired with Magnetic Starters, Single-Stage needs no Magnetic Starter
  • 2 Year Limited Warranty
    On-site Parts and Labour
DV SDI Series 5 / 13 HP Reciprocating Air Compressors Highlights
Engine Option 13 Horse Power (HP)
Gas powered
Motor Output 5, 7.5, 10 Horse Power (HP)
Air Capacity Delivery 13 to 21 Standard cubic feet per minute at 150 psi
Compressor Pump Type DEV40, DEV55 and DEV100
Technology Splash Lubrication
Motor Revolutions per Minute (RPM) RPM 890/1100
Engine is 3,600 rpm
Electrical Power Motor ODP (Open Drip Proof)
Single Phase
120V/20.4-32A, 230V/16A, 60Hz
Three Phase
575V/3.1-8.2A, 60Hz
DV SDI Series Models
  • True five hp, 19.7 amp industrial motor with internal overload protection
  • High amp load rated pressure switch
  • Cast iron, single stage, three cylinder pump
  • 60-gallon vertical air receiver
  • Maximum operating pressure 125 PSI
  • Cast iron, two stage, three cylinder pump with oil sight gauge
  • True 5hp industrial ODP motor
  • Magnetic starter and wiring harness installed
  • 80-gallon vertical air receiver
  • Maximum operating pressure 150 PSI
DV SDI MODELS IS5-10080 / IS7-10080 / ISIO – 100120
  • Cast iron, two stage, four cylinder pump with oil sight gauge
  • Stainless steel disc valves
  • Industrial grade ODP motor
  • Magnetic starter and wiring harness installed
  • 80 and 120-gallon air receiver available (IS510080H and IS7-100120)
  • Maximum operating pressure 150 PSI
Refrigerated Air Dryers

A refrigerated air dryer when sized correctly, lowers the temperature of the compressed air allowing water to condense and be removed from the air system. A system without an air dryer will always have an unacceptable amount of moisture for any tool, valve, or actuator and consequently will shorten their service life.


All ProDry™ ASD air dryers are microprocessor controlled and come with an energy saving heat exchanger, high-efficiency condensate separator, and large surface area Freon condenser. An incorporated safety shut-off protects the air compressor in the event of a fault in the air dryer function or running at temperatures above identified standards.


  • ProDry™ HTD High Inlet Temperature Air Dryers deal with temperatures up to 180° F.
  • Supplied with a variable-speed fan to retain a balanced dew point.
  • Cross ventilated to facilitate installation in close proximity to walls.

Installation Kit Part # IK515
Includes steel flex hose and four vibration isolators.

Maintenance Kit (Order by model)
Includes oil and air filter for one maintenance period.

Air Dryer
Refrigerated or High-Temperature inlet available.

Electronic Zero Loss Auto Drain Part # KK-9860
An electronic drain makes certain that potential condensate is removed from the air receiver tank regularly, resulting in peak system performance.

DF SERIES Air Filters For Compressed Air DV Systems Comprehensive line of filters that efficiently removes up to 99.99% of impurities, including oil aerosols and small particles of dust, serving to increase system function while reducing downtime.